Mon-Fri: 7:30am - 5:15pm | Sat: 8:00am - 1:00pm

By HPM Bouhandelaars · Updated · 5 min read · Tools and electrical

In short

  • Masonry bits have a carbide tip and are used with hammer action in brick, block and concrete.
  • HSS bits are for metal; cobalt HSS bits handle stainless steel and other hard metals.
  • Wood bits have a centre point: brad-point for clean holes, spade (flat) bits for larger holes.
  • Tile and glass bits have a spear-shaped tip - always with hammer action off.
  • The shank must suit the drill: round or hex shanks for a normal chuck, SDS-plus for rotary hammers.

A drill is only as good as the bit in it. The wrong bit burns in wood, skates across a tile, goes blunt in seconds on steel or simply refuses to enter concrete. The right one cuts cleanly with little effort. Drill bits are made for a material, and once you know what to look for you can tell them apart at a glance. This guide covers the four families most people need - masonry, metal, wood and tile - and how to use each.

Masonry bits: brick, block and concrete

A masonry bit has a tip of tungsten carbide, a very hard material, brazed into a slot at the end of a steel shaft. The tip is wider than the shaft and looks like a small flat arrowhead. It does not slice the material; it chips and crushes it while the spiral flutes carry the dust out.

  • Use hammer action. In brick, concrete and stone, set the drill to hammer mode. Soft materials such as some cement blocks and mortar joints drill without it.
  • Standard-shank masonry bits fit an ordinary chuck and are fine for wall plugs in brick and plaster.
  • SDS-plus bits fit rotary hammer drills. The slotted shank lets the bit slide as the hammer mechanism strikes it, so it drills hard concrete far faster than a hammer drill. If you regularly drill concrete, lintels or reinforced slabs, an SDS-plus rotary hammer and bits are worth having.
  • Clear the dust. Pull the bit back every centimetre or two in deep holes. A hole packed with dust overheats the tip and gives a wall plug nothing to grip.

If the bit suddenly stops making progress in concrete, you may have hit reinforcing steel. Do not force it; move the hole.

Metal bits: HSS and cobalt

Bits for metal are made of high-speed steel (HSS). They are one piece of steel with two sharp cutting edges ground at the tip, and they cut a continuous curl of metal.

  • Plain HSS is for mild steel, aluminium, brass and copper. HSS bits also drill wood and plastic neatly.
  • Coated HSS (for example gold-coloured titanium nitride) runs cooler and lasts longer in general use. The coating is on the surface, so it is lost at the tip when the bit is resharpened.
  • Cobalt HSS has cobalt alloyed into the steel, which keeps it hard when hot. Use it for stainless steel and other hard metals.
  • Step drills cut a range of hole sizes in thin sheet metal and leave a clean, round hole.

Technique matters more with metal than with anything else. Mark the centre with a centre punch so that the bit does not wander. Use a slow speed - the larger the bit and the harder the metal, the slower - with firm, steady pressure and a drop of cutting oil. For holes over about 8 mm, drill a smaller pilot hole first. Clamp the workpiece: thin metal can catch on the bit as it breaks through and spin.

Wood bits

  • Brad-point bits have a sharp centre point and two spurs that score the outline of the hole before the edges cut. The point stops the bit wandering and the spurs leave a clean edge. They are the general-purpose wood bit.
  • Spade (flat) bits drill larger holes quickly, for example for pipes and cables through timber. They are rough on the exit side, so drill until the point just shows, then finish from the other side.
  • Auger bits have a screw tip that pulls the bit in and deep flutes that clear the chips, for deep holes in thick beams and posts.
  • Forstner bits cut flat-bottomed holes, such as for concealed cupboard hinges.
  • Hole saws cut large round holes in timber, board and sheet materials.
  • Countersink bits make the cone-shaped recess that lets a screw head sit flush.

Do not use hammer action in wood. Pre-drilling a pilot hole stops timber splitting near board ends, which matters with the stainless steel screws used at the coast - see galvanised vs stainless steel fasteners.

Tile and glass bits

Tile and glass bits have a spear-shaped carbide tip that grinds its way through the hard glaze. For hard porcelain tiles, a diamond-tipped bit or diamond hole saw is the better tool.

  • Hammer action off, always. Hammering cracks tiles.
  • Slow speed, light pressure. Let the bit do the work.
  • Stop the bit skating. Stick masking tape over the mark, or start at a slight angle and straighten up once the tip has bitten.
  • Keep it cool. A little water on the tip stops the bit and the tile overheating. Diamond bits in particular need water.
  • Change bits behind the tile. Once through the tile, switch to a masonry bit of the same size to drill the wall behind it.
  • Stay away from edges and drill through the tile rather than on a grout line where you can, since a plug in grout tends to work loose.

Shanks, sizes and sets

  • Round shank: fits any standard three-jaw chuck.
  • Hex shank: six-sided, for quick-change chucks and impact drivers, and it cannot slip in the chuck.
  • SDS-plus: for rotary hammers only. It does not fit a standard chuck without an adaptor.

Sizes are the diameter in millimetres. For wall plugs, the bit size is the plug size: a 6 mm plug needs a 6 mm masonry bit, and the plug packet tells you which screw sizes fit. For screws in timber, the pilot hole should be about the diameter of the screw's core, not its thread. A set covering the common sizes costs less than buying the same bits one by one; top it up with single bits in the sizes you wear out. HPM stocks drill bits from Alpen, Tork Craft and Tolsen, among others.

Technique and safety

  • Wear safety glasses for all drilling, and a dust mask when drilling masonry, especially overhead.
  • Check what is behind the surface. Pipes and cables usually run straight up, down or sideways from taps, plugs and switches. Avoid those lines or use a detector.
  • Clamp small work and keep both hands on the drill. Use the side handle on a hammer drill; a jammed bit can twist the drill out of your hand.
  • Do not wear loose gloves or sleeves near a spinning bit.
  • Let a hot bit cool. A bit that turns blue at the tip has been overheated and softened.
  • A blunt bit is a sign, not something to push through. Squealing, smoke, dust instead of chips or shavings and a lot of pressure all mean the bit is blunt or the wrong type.

What you need

These links open the matching products in the HPM online store, with live prices (incl. VAT) and stock.

Questions and answers

How can I tell a masonry bit from a metal bit?

A masonry bit has a wider, flat tip of tungsten carbide brazed into the end, like a small arrowhead. A metal (HSS) bit is one piece of steel with sharp cutting edges ground at the tip and is usually black, gold or bright silver.

Can I use a masonry bit on tiles?

It is not a good idea. Use a tile and glass bit with a spear-shaped carbide tip, or a diamond bit for hard porcelain, with hammer action switched off and a slow speed. Hammer action cracks tiles.

Which drill bit do I need for stainless steel?

Use a cobalt HSS bit, run the drill slowly with firm, steady pressure and use cutting oil. Stainless steel hardens if the bit spins fast without cutting, which then blunts ordinary bits very quickly.

What does SDS mean?

SDS is a slotted shank system for rotary hammer drills. The bit clicks into the chuck without a key and can slide slightly, which lets the hammer mechanism hit much harder than a normal hammer drill. SDS-plus is the common size for home and site use; SDS bits do not fit a standard three-jaw chuck.

Which power tools should a DIYer buy first?

A good cordless drill/driver is the most useful first tool, followed by an angle grinder, jigsaw or circular saw depending on your projects. Staying with one battery platform saves money because the batteries and chargers can be shared across tools.

Delivery from HPM

Parcels up to 50 kg are delivered by courier anywhere in South Africa, with the rate shown at checkout. Heavy building materials such as cement, bricks, sand, stone and timber are delivered by our own trucks in the Western Cape, and any order can be collected free in Struisbaai.

WhatsApp 076 370 4367 for a quote, call 028 435 6331 or email [email protected].

General guidance only. Products, sites and building rules differ - always follow the product data sheet and your approved plans, and check with your municipality or a registered professional where the work is structural, electrical or needs approval. More short answers: Building Facts & Advice.