Mon-Fri: 7:30am - 5:15pm | Sat: 8:00am - 1:00pm

By HPM Bouhandelaars · Updated · 5 min read · Building at the coast

In short

  • Near the sea, use hot-dip galvanised or stainless steel fixings. Grade 316 (A4) stainless is best close to the sea.
  • Ordinary bright or zinc-plated (electroplated) fixings rust quickly in salt air and stain the paint and timber around them.
  • Hot-dip galvanising is a much thicker zinc coat than zinc plating. It is not the same thing, even though both look silver.
  • Do not mix stainless and galvanised parts in one connection: the galvanised part corrodes faster.
  • Match the fixing to the material: treated timber and coastal roof sheeting each need fixings made for them.

On a coastal building the screws, nails and bolts are usually the first things to fail. They are small, they are made of steel and they sit exactly where water collects. A deck or a roof is only as durable as what holds it together, so choosing the right fixing is not a detail - it decides how long the whole job lasts. This guide compares the common finishes and explains which to use where.

Why fixings fail first

Salt in the air speeds up the corrosion of steel. In seaside towns the air carries salt well inland on the wind, and it settles in the places rain does not wash: under eaves, behind cladding, inside joints. A fixing also suffers more than the material around it. Its head is scratched by the driver bit, it is under stress, and it often sits in a hole where moisture lingers. Once the protective coating is broken, rust spreads, the fixing loses strength and brown streaks stain the paint and timber around it.

The options, from least to most resistant

Bright (uncoated) steel

Plain steel nails and screws with no coating. They are for dry, indoor work that will stay dry. Outdoors at the coast they rust quickly.

Zinc-plated, also called electro-galvanised

These have a thin, bright, smooth zinc coat applied by electroplating, sometimes with a yellow tint. Most ordinary chipboard screws and small bolts are finished this way. The coat is thin, so it suits indoor use and sheltered inland conditions. At the coast it does not last outdoors.

Hot-dip galvanised

The fixing is dipped in molten zinc, which leaves a much thicker, duller grey coat that is slightly rough. The zinc protects the steel by corroding slowly in its place, so a thicker coat means a longer life. Hot-dip galvanised nails, bolts, coach screws and brackets are the standard choice for outdoor structural timber work. Very close to the sea the zinc is used up faster, and stainless steel becomes the better choice.

Coated exterior screws

Many decking and roofing screws carry a multi-layer or ceramic-type coating over the steel. These perform better outdoors than plain zinc plating. Performance differs between makes, so check what exposure the maker rates the screw for, and whether it is rated for treated timber.

Stainless steel: A2 (304) and A4 (316)

Stainless steel does not rely on a coating; the metal itself resists corrosion. Fasteners are marked A2 or A4. A2 is grade 304, the general-purpose stainless steel. A4 is grade 316, which contains molybdenum and stands up better to salt. Grade 316 is best close to the sea. A2 is widely used further back from the shore and in positions that rain washes regularly.

Which to use where

JobSensible choice at the coast
Indoor joinery, cupboards, dry roof spaceZinc-plated is usually fine
Decks, pergolas, fences, outdoor stairsStainless steel screws; hot-dip galvanised or stainless bolts and brackets
Roof sheetingCoastal-grade roofing screws with sealing washers, matched to the sheeting
Gutters, fascias, claddingStainless steel or hot-dip galvanised
Balustrades, shade sails, anything facing the seaGrade 316 (A4) stainless steel
Anchors into brick and concrete outdoorsStainless steel or hot-dip galvanised anchors, not plain zinc-plated

Two materials need special thought. Treated timber: the copper in many timber preservatives attacks plain and zinc-plated steel, so use hot-dip galvanised or stainless steel fixings in treated pine. Roof sheeting: choose sheeting with a coating rated for coastal or marine environments and fit it with matching coastal-grade screws and washers, as the sheeting maker specifies. For structural connections - roof tie-downs, truss hangers, balustrades - follow the engineer's or truss designer's specification rather than a general guide.

Mixing metals

Avoid mixing stainless steel and galvanised parts. When different metals touch in damp, salty air, galvanic corrosion eats away the weaker metal - usually the galvanised part. A stainless bolt through a galvanised bracket, for example, can strip the zinc around the hole. Use one type of metal throughout a connection: bolt, nut, washer and bracket. Where two metals must meet, separate them with a washer or sleeve that does not conduct electricity, such as nylon or rubber. The same applies to aluminium, which corrodes where it touches stainless steel or copper in salt air.

Working with stainless steel

  • Pre-drill. Stainless screws are softer than hardened steel screws and can snap or strip in hard timber. Drill a pilot hole and drive at a moderate speed.
  • Use the right bit. A worn or wrong-size driver bit chews the head. Square and Torx drive screws grip better than Phillips.
  • Mind the threads. Stainless nuts and bolts can seize ("gall") when tightened fast and dry. Tighten slowly and use a little lubricant or anti-seize on the thread.
  • Keep steel dust away. Grinding or wire-brushing ordinary steel next to stainless leaves particles that rust on its surface. Use clean tools.

Looking after fixings

Rinse exposed metal with fresh water now and then, especially under overhangs where rain never reaches. Brown surface marks on stainless steel ("tea staining") are usually cosmetic and wash off with a mild cleaner. Check roofing screws and structural bolts once a year and replace any that show red rust, loose heads or perished washers before they let go. When you drill out an old fixing to replace it, see our guide to choosing drill bits.

What you need

These links open the matching products in the HPM online store, with live prices (incl. VAT) and stock.

Questions and answers

Which nails, screws and bolts should I use near the sea?

Use hot-dip galvanised or stainless steel fixings - grade 316 stainless is best close to the sea. Ordinary bright or electroplated fixings rust quickly in salt air and stain the surrounding paint and timber.

Can I mix stainless steel and galvanised fixings?

Avoid it. When different metals touch in damp, salty air, galvanic corrosion eats away the weaker metal - usually the galvanised part. Use one type of metal throughout a connection, or separate the metals with a washer or sleeve that does not conduct electricity.

What is the difference between A2 and A4 stainless steel?

A2 is the fastener marking for grade 304 stainless steel and A4 is the marking for grade 316. Grade 316 contains molybdenum, which gives it better resistance to salt, so A4 is the better choice close to the sea. A2 is widely used further from the shore and in sheltered positions.

Is zinc-plated the same as galvanised?

No. Zinc-plated (electro-galvanised) fixings have a thin, bright zinc coat meant for dry indoor use. Hot-dip galvanised fixings are dipped in molten zinc and carry a much thicker, duller coat that lasts far longer outdoors.

Does stainless steel rust?

It can show brown surface staining (often called tea staining) in salt air, especially where rain does not wash it. This is usually cosmetic. Rinsing with fresh water now and then keeps it clean; grade 316 stains less than grade 304.

Delivery from HPM

Parcels up to 50 kg are delivered by courier anywhere in South Africa, with the rate shown at checkout. Heavy building materials such as cement, bricks, sand, stone and timber are delivered by our own trucks in the Western Cape, and any order can be collected free in Struisbaai.

WhatsApp 076 370 4367 for a quote, call 028 435 6331 or email [email protected].

General guidance only. Products, sites and building rules differ - always follow the product data sheet and your approved plans, and check with your municipality or a registered professional where the work is structural, electrical or needs approval. More short answers: Building Facts & Advice.