In short
- Gypsum board (Rhino board) is the standard ceiling in South African homes; use moisture-resistant or fibre-cement board where it is damp or outdoors.
- Joints are either covered with strips or taped and skimmed for a flush, seamless ceiling.
- Cornices cover the gap between wall and ceiling; lightweight XPS cornices are glued up and painted.
- Insulation is rated by R-value. The thickness you need depends on the product and on where in the country you build.
- New homes and additions must meet the energy rules in SANS 10400-XA, so the insulation is specified on the plans.
The ceiling and the insulation above it do more for the comfort of a house than almost anything else you can add. Together they keep heat out in summer and in during winter, quieten the rain on a metal roof and hide the roof structure. This guide covers the ceiling board options, how ceilings are fixed and finished, how to choose a cornice, and how to think about insulation - where the right question is not "how thick?" but "what R-value?".
Ceiling board options
Gypsum board (Rhino board)
Gypsum plasterboard, known everywhere in South Africa as Rhino board after the best-known brand, is the standard ceiling in homes. It is a gypsum core between paper faces: flat, easy to cut and fix, and it paints well. It comes in several thicknesses. Thinner boards are used for ceilings with covered joints, and thicker boards are used where the ceiling will be taped and skimmed flush. Standard gypsum board is for dry rooms only.
Moisture-resistant and fibre-cement boards
Bathrooms, kitchens, laundries and covered stoeps are humid or exposed. Use moisture-resistant gypsum board indoors where steam is the problem, and fibre-cement board for eaves, carports, open verandas and other places the weather can reach. Fibre-cement does not swell or sag when it gets damp. At the coast, sea mist reaches a long way under open eaves, so fibre-cement is the safe choice outside.
PVC ceiling panels
Tongue-and-groove PVC panels clip together, need no painting and are unaffected by moisture. They suit bathrooms, kitchens and garages.
Fixing and jointing
Ceiling boards are fixed to brandering - timber battens fixed across the underside of the roof trusses - or to a steel ceiling grid. The spacing of the brandering and of the screws or nails depends on the board thickness, so follow the board maker's fixing guide: a board that spans too far sags over time.
There are two ways to deal with the joints:
- Covered joints. Boards are butted together and the joints covered with jointing strips (H-profile strips between boards or flat cover strips). It is quick and economical, and the lines stay visible.
- Flush-plastered ceiling. Joints are taped and filled with joint filler, and the whole ceiling is usually skimmed with a thin coat of gypsum skim plaster for a smooth, seamless finish. It takes more skill, and it is less forgiving of roof movement.
Use drywall screws driven just below the surface without tearing the paper, and prime new gypsum and skim plaster before painting. Leave a trapdoor for access to the roof space.
Cornices
A cornice covers the joint between the wall and the ceiling, which would otherwise crack as the roof moves with heat and wind. The main types are:
- Gypsum cove cornice: the traditional curved profile, fixed with cornice adhesive and painted.
- XPS or polystyrene cornice: very light, cut with a sharp knife or fine saw in a mitre box and glued up with a suitable adhesive. HPM stocks XPS cornices in a range of profile sizes, from about 40 mm to over 130 mm.
- Shadow-line (no cornice): a recessed gap formed with a metal or plastic trim, for a modern look.
Solvent-based adhesives and paints can melt polystyrene, so use an adhesive and a water-based paint that the cornice maker says are suitable. Fill the mitres and the top and bottom edges with a flexible paintable filler before painting.
Roof insulation: how it works
Insulation slows the flow of heat. In summer the roof covering gets very hot and radiates heat downwards; in winter warm air inside rises and escapes through the ceiling. There are two broad kinds:
- Bulk insulation traps still air. It comes as blankets or rolls of glass wool or polyester fibre laid on top of the ceiling between and over the brandering, or as rigid boards (such as XPS or polyisocyanurate) used above exposed-rafter ceilings and under flat roofs.
- Reflective insulation is a foil layer, usually installed under the roof covering, that reflects radiant heat. It needs an air space next to the shiny face to work, and it also acts as a second line of defence against dust and wind-driven rain.
Many roofs use both: reflective foil under the sheeting or tiles and a blanket on the ceiling.
How thick should insulation be?
Insulation is rated by its R-value, its resistance to heat flow. The higher the R-value, the better it insulates. Thickness on its own tells you little, because different materials reach the same R-value at different thicknesses. The pack or data sheet states the R-value for each thickness.
For new houses and additions, SANS 10400-XA sets energy efficiency rules that include insulation in the roof. The total R-value required for the roof depends on the climate zone the house is in and on the roof construction, and the plans must show how the house complies. In practice that means:
- New build or addition: use the insulation type and thickness specified on your approved plans. If you want to substitute a product, match or beat the specified R-value and confirm it with the designer.
- Existing house: you are free to choose. Thicker blankets insulate better, so buy the best R-value your budget and roof space allow. Blankets are commonly sold in several thicknesses, from about 50 mm to 135 mm and more.
Do not squash a thick blanket into a shallow space; compressed insulation loses much of its value.
Installing insulation safely
- Walk only on the trusses and brandering. Ceiling board will not carry your weight.
- Cover up. Wear a dust mask, gloves, long sleeves and eye protection; fibres and roof dust irritate skin and lungs.
- Lay the blanket snugly with no gaps, right to the edges, without blocking the ventilation at the eaves.
- Keep clear of heat. Recessed downlights, their transformers and flues can overheat if covered. Keep the clearances the light and insulation makers give, or use fittings rated to be covered.
- Leave electrical work alone. Do not move or alter wiring in the roof; that is work for a registered electrician.
- Geysers. Keep the area around the geyser, its drip tray and its valves accessible.
Ceiling boards, long cornices and insulation rolls are bulky. Not everything is listed in the online store, so send HPM your ceiling area and ask what is available and for a quote. Bulky items are delivered by our own trucks in the Western Cape or collected in Struisbaai, while screws, joint filler, adhesive and paint can be couriered anywhere in South Africa.
What you need
These links open the matching products in the HPM online store, with live prices (incl. VAT) and stock.
- Cornices - XPS cornices in several profiles
- Roof and ceiling products - cornices, gutters and truss bracing strap
- Drywall screws - for fixing gypsum board
- Joint filler and skim plaster - for taped and skimmed joints
- Skimming plaster
- Plastering trowels
- Ceiling paint and ceiling products - wall and ceiling paints, ceiling fans and fittings
- Dust masks and safety gear - wear a mask, gloves and glasses in the roof space
Questions and answers
What is the best ceiling board for a bathroom?
Bathrooms and kitchens are humid, so use a board made for it: moisture-resistant gypsum board, fibre-cement board or PVC ceiling panels, with good ventilation. Standard gypsum board sags and stains where steam condenses on it.
How thick must roof insulation be?
There is no single thickness. Insulation is specified by R-value, and the R-value a roof needs depends on the climate zone and the roof construction. Different products reach the same R-value at different thicknesses, so compare R-values on the data sheets and follow what your plans specify.
Is roof insulation compulsory in South Africa?
For new buildings and additions, yes: SANS 10400-XA sets energy efficiency rules that include insulation in the roof, and the plans must show how the house complies. Existing homes are not forced to upgrade, but insulation is one of the most effective comfort improvements.
Can I lay insulation over downlights?
Not unless the light fitting and the insulation maker both say it is safe. Recessed downlights and their transformers can overheat when covered. Keep the clearances given by the manufacturers or use fittings rated to be covered, and ask an electrician if you are unsure.
Does HPM deliver ceiling boards and cornices?
Full-length boards and cornices are bulky items that travel on HPM's own trucks in the Western Cape or can be collected in Struisbaai. Smaller items such as screws, joint filler and paint go by courier anywhere in South Africa.
Related guides
Delivery from HPM
Parcels up to 50 kg are delivered by courier anywhere in South Africa, with the rate shown at checkout. Heavy building materials such as cement, bricks, sand, stone and timber are delivered by our own trucks in the Western Cape, and any order can be collected free in Struisbaai.
WhatsApp 076 370 4367 for a quote, call 028 435 6331 or email [email protected].
General guidance only. Products, sites and building rules differ - always follow the product data sheet and your approved plans, and check with your municipality or a registered professional where the work is structural, electrical or needs approval. More short answers: Building Facts & Advice.