Mon-Fri: 7:30am - 5:15pm | Sat: 8:00am - 1:00pm

By HPM Bouhandelaars · Updated · 6 min read · Building at the coast

In short

  • Most leaks start at joints: flashings, parapets, roof screws, overlaps, ridges and outlets - not in the middle of the roof.
  • A liquid acrylic or rubberised waterproofing coat with a reinforcing membrane bedded into it is the usual DIY system for those joints.
  • Salt speeds up rust, so treat and prime metal before you coat it and use coastal-grade fixings.
  • Preparation and dry weather matter more than the brand: clean, dry, sound and primed surfaces, and the full number of coats on the tin.
  • Inspect every year. Flat concrete roofs and badly rusted sheeting are jobs for a waterproofing contractor.

A roof near the sea works harder than one inland. Salt settles on it every day, the wind drives rain sideways under flashings and the sun bakes everything in between. HPM is in Struisbaai on the Western Cape coast, so coastal conditions are what we deal with every day. This guide explains where coastal roofs leak, which waterproofing systems suit which part of the roof and how to apply them so that they last.

Why coastal roofs leak sooner

Salt in the air speeds up the corrosion of steel, fixings and roof sheeting, and it breaks paint and coatings down faster than inland. Three things then work together:

  • Rust. Roof screws, washers, flashings and the cut edges of sheeting rust first. A rusted screw loosens, its washer perishes and the hole lets water in.
  • Movement. Metal sheeting and flashings expand in the sun and shrink at night. Rigid fillers and old paint crack along joints that move.
  • Wind-driven rain. In a south-easter or a winter north-wester, rain is pushed up under overlaps, ridge cappings and parapet flashings that are perfectly dry in gentle rain.

Areas that the rain never reaches, such as under eaves and overhangs, often rust fastest because the salt is never washed off.

Find where the water gets in

Water travels. A stain on the ceiling is often a metre or more from the hole in the roof, because the water runs along a purlin, a truss or the underside of a sheet before it drips. Before you buy anything, look at the roof from outside and, if you can do it safely, from inside the roof space with a torch. Check these places first:

  • flashings where the roof meets a wall, chimney or parapet;
  • the tops and inside faces of parapet walls, especially cracks in the plaster;
  • roof screws and their washers, and the side and end overlaps of sheets;
  • ridge and hip cappings, and broken or slipped tiles;
  • box gutters, valleys and outlets, which block with leaves and sand;
  • anything that passes through the roof: vent pipes, skylights, solar geyser pipes and aerial brackets.

Working on a roof is dangerous. Use a secured ladder, never walk on fibre-cement or brittle sheeting, stay off a wet or windy roof and get a contractor in for steep or high roofs.

Waterproofing systems and where each one fits

Liquid waterproofing with a membrane

This is the usual system for joints and details. A flexible acrylic or rubberised liquid is brushed on, a strip of reinforcing membrane (a polyester fabric) is bedded into the wet coat, and further coats are applied until the fabric is completely covered. The fabric gives the coating the strength to bridge a joint that moves. Use it on flashings, parapet tops, around pipes and over roof screws and overlaps.

Fibre-reinforced and rubberised coatings

Some liquid waterproofers contain fibres or rubber so that they can be used without a separate membrane on small cracks and screw heads. They are convenient for maintenance, but a proper joint or a parapet still needs fabric.

Torch-on membrane

Flat concrete roofs, balconies and large box gutters are normally sealed with a bitumen sheet that is heated and bonded to the surface. It is applied with a gas torch and is work for a waterproofing contractor, not a DIY job. The membrane is then protected from the sun with a reflective coating.

Sealants and waterproofing tape

Polyurethane sealant and self-adhesive waterproofing tape are useful for small gaps, laps and emergency repairs. Treat them as part of a repair, not as the whole system.

How to apply a liquid membrane system

The steps below are the general method. The instructions on the tin always come first.

  1. Choose the weather. The surface must be dry and no rain or heavy dew should be expected before the coat dries. Avoid the hottest part of the day and strong wind.
  2. Clean. Remove dust, salt, moss, loose paint and old flaking waterproofing. Wash with fresh water and let the surface dry completely.
  3. Deal with rust. Wire-brush loose rust, treat what is left with a rust converter and prime bare metal. Replace rusted screws with new roofing screws and washers. Replace sheets that have rusted through.
  4. Repair. Fill cracks in parapets and plaster and fix loose flashings before you coat anything.
  5. Prime where the product calls for it. Many waterproofers are thinned for the first coat on porous surfaces.
  6. First coat and membrane. Brush on a generous coat, lay the membrane into it while it is wet and brush it flat so that there are no bubbles or dry patches. Overlap strips of membrane.
  7. Saturate. Apply a second coat straight over the membrane so that the fabric is soaked through.
  8. Finish coats. Once dry, apply the further coats that the tin specifies, each at right angles to the previous one, until the weave of the fabric no longer shows.

The most common mistake is to spread the product too thinly. Waterproofing works because of its thickness, so use the quantity per square metre that the maker gives.

Roof paint is the finish, not the repair

Roof paint protects sheeting and tiles from sun and salt and makes an old roof look new, but it does not seal a moving joint. Do the waterproofing first, then paint. New galvanised sheeting needs a galvanised iron cleaner and primer before paint will stick to it. For new roofs at the coast, choose sheeting with a coating rated for coastal or marine conditions and fit it with matching coastal-grade screws and washers - see our guide to galvanised and stainless steel fasteners.

Yearly maintenance at the coast

  • Inspect the roof once a year, ideally before the winter rain, and after any big storm.
  • Clear gutters, valleys and outlets.
  • Wash down sheeting where rain does not reach, such as under overhangs, to remove salt.
  • Touch up cracked or lifted waterproofing straight away - most leaks start there.
  • Replace rusted screws before the washers fail.

If a ceiling stays wet after repairs, if a concrete roof ponds water or if roof timber has been wet for a long time, get a waterproofing contractor or an engineer to look at it. Damp that shows low down on walls is a different problem: see damp-proofing basics.

What you need

These links open the matching products in the HPM online store, with live prices (incl. VAT) and stock.

Questions and answers

What is the best waterproofing for a roof near the sea?

There is no single best product. For joints, flashings, parapets and roof screws, a liquid acrylic or rubberised waterproofing coat with a reinforcing membrane bedded into it works well. Roof sheeting needs a coating rated for coastal conditions and coastal-grade screws. Flat concrete roofs usually need a torch-on membrane fitted by a contractor.

Can I waterproof over rust?

No. Remove loose rust with a wire brush, treat what remains with a rust converter and prime the metal first. Waterproofing applied over active rust lifts as the rust keeps growing underneath. Sheets that have rusted through should be replaced.

How often should waterproofing be redone?

Inspect it every year. Most leaks start where a membrane has cracked or lifted, so small repairs done early save a full re-coat. How long a system lasts depends on the product, the sun and salt exposure and how well it was applied - follow the maker's maintenance advice.

Can I apply waterproofing in winter?

Yes, as long as the surface is completely dry and no rain or heavy dew is expected before the coat has dried. Water-based products need dry weather to cure, so plan the work for a settled spell and stop early enough in the day for the last coat to dry.

Is roof paint the same as waterproofing?

No. Roof paint protects and colours sheeting and tiles, but it does not bridge gaps or moving joints. Fix leaks with a waterproofing system first, then paint.

Delivery from HPM

Parcels up to 50 kg are delivered by courier anywhere in South Africa, with the rate shown at checkout. Heavy building materials such as cement, bricks, sand, stone and timber are delivered by our own trucks in the Western Cape, and any order can be collected free in Struisbaai.

WhatsApp 076 370 4367 for a quote, call 028 435 6331 or email [email protected].

General guidance only. Products, sites and building rules differ - always follow the product data sheet and your approved plans, and check with your municipality or a registered professional where the work is structural, electrical or needs approval. More short answers: Building Facts & Advice.