In short
- A DPC is a strip of plastic membrane built into the wall just above ground level; a DPM is the plastic sheet under a concrete floor slab.
- Together they stop ground moisture rising into walls and floors.
- Not all damp is rising damp: check for rain getting in, leaking pipes and condensation first.
- Fix the cause, let the wall dry, then treat and paint. Paint alone never cures damp.
- Keep soil, paving and plaster from bridging the DPC - that is the most common reason a working DPC stops working.
Bricks, mortar, plaster and concrete are porous. Left in contact with damp ground they soak water up like a wick, and the water carries salts that push paint and plaster off the wall. Two hidden layers of plastic stop this in a properly built house: the damp-proof course (DPC) in the walls and the damp-proof membrane (DPM) under the floor. This guide explains what they do, how to tell rising damp from the other kinds of damp, and how to put each one right.
What DPC and DPM are
Damp-proof course (DPC)
A DPC is a strip of plastic membrane built into the wall that stops ground moisture rising into the brickwork. It is placed in walls just above the ground and floor level - typically at least 150 mm above finished ground level - and lapped properly at joints. DPC is also built in wherever water could cross into the dry part of a wall: under window sills, above lintels in cavity walls and under the copings of parapet walls.
Damp-proof membrane (DPM)
A DPM is the plastic sheet laid on the prepared ground before a concrete floor slab is cast. The sheets are overlapped and sealed at the joins, laid on a smooth layer of sand so that stones do not puncture them, and turned up at the edges to meet the DPC in the walls. Floor and walls are then cut off from the ground by one continuous barrier.
The thickness and type of DPC and DPM are set out in the building regulations and on your approved plans. Use what the plans specify; a thin plastic sheet that is not made for the purpose tears and perishes.
Four kinds of damp and how to tell them apart
| Kind | Where it shows | Typical cause |
|---|---|---|
| Rising damp | Low down on ground-floor walls: a tide mark, blistered paint, white powdery salts, crumbling plaster near the skirting | Missing, damaged or bridged DPC |
| Penetrating damp | Patches at any height, often on the weather side, around windows, below parapets and roofs; worse after rain | Cracks, failed sealant or flashing, porous walls, leaking gutters |
| Plumbing leaks | A patch that stays wet in dry weather, often near a bathroom, kitchen or geyser | A leaking pipe, waste or shower |
| Condensation | Mould in corners, behind cupboards and on cold outside walls and ceilings; water on windows | Moist indoor air and poor ventilation |
Start with the simple checks. Does the patch grow after rain or stay the same? Is there a tap, pipe or shower on the other side of the wall? Is the outside ground higher than the inside floor? Treating the wrong kind of damp wastes money: no damp-proofing paint will cure a leaking shower.
When a good DPC is bridged
Many cases of rising damp are not a failed DPC at all. The DPC is intact, but something gives water a path around it. Look for:
- garden soil, flower beds or paving built up against the wall to above the DPC line;
- plaster that runs unbroken from the wall down to the ground, covering the DPC;
- a screed, step or stoep cast against the wall above DPC level;
- mortar droppings that filled the bottom of a cavity wall during building.
Lowering the ground, cutting the plaster back above the DPC line and making sure paving slopes away from the house often solve the problem without any chemical treatment. When you lay new paving, keep its finished level well below the DPC - see laying paving.
Fixing rising damp
- Remove the bridge and improve the drainage around the house, as above. Fix leaking gutters and downpipes that soak the base of the wall.
- Where the DPC is missing or broken, a new barrier can be made by injecting a damp-proofing fluid or cream into a line of holes drilled into the wall near its base. The product spreads through the masonry and forms a water-repellent band. Hole spacing, depth and quantity are set by the product instructions and must be followed exactly; many owners use a damp-proofing contractor for this.
- Remove the damaged plaster to well above the highest damp mark. It is full of salts that keep drawing moisture out of the air, so it will not dry properly even after the damp is stopped.
- Let the wall dry. Brickwork dries slowly - allow weeks, not days, with good ventilation.
Fixing penetrating damp and condensation
Penetrating damp is fixed from the outside. Fill cracks with a flexible exterior crack filler, re-seal around window and door frames, repair flashings and parapet waterproofing, clear gutters and repaint with a quality exterior acrylic. Our guides to coastal roof waterproofing and exterior paint for coastal homes cover these repairs. Wider cracks, or cracks that keep growing, should be checked by a professional before you fill them.
Condensation is fixed by moving moist air out: open windows, fit or use extractor fans in bathrooms and kitchens, vent tumble dryers outside and leave a gap behind cupboards on outside walls. Clean mould with a fungicidal wash before repainting.
Plumbing leaks need a plumber. Fix the pipe before anything else.
Replastering and repainting
Once the cause is fixed and the wall has dried, replaster the stripped area, keeping the new plaster clear of the floor and of the DPC line so that you do not create a new bridge. Let the new plaster cure - often around four weeks in good weather - then prime with an alkali-resistant plaster primer and finish with the top coats. Where the paint maker's system includes a damp-sealing primer for walls that have had damp, use it as directed. It is a finishing step, not a cure: painting over damp alone will not solve it.
Building a new house or an extension? Then the DPC and DPM are part of your approved plans and will be checked by the building inspector. Make sure they go in properly while the walls and floors are open, because they are very difficult to fix afterwards.
What you need
These links open the matching products in the HPM online store, with live prices (incl. VAT) and stock.
- Damp sealers and damp-proofing treatments - damp-seal paints and injection fluid
- Waterproofing products - liquid waterproofers, membrane and bitumen products
- Crack fillers - close cracks that let rain in
- Sealants - around window and door frames
- Bonding liquid - for patching plaster
- Plaster primers - prime repaired plaster before painting
- Paint scrapers - remove blistered paint and loose plaster
- Masonry drill bits - for drilling injection holes
Questions and answers
What is a damp-proof course and where does it go?
A damp-proof course (DPC) is a strip of plastic membrane built into the wall that stops ground moisture rising into the brickwork. It is placed in walls just above the ground and floor level - typically at least 150 mm above finished ground level - and lapped properly at joints. Without it, walls stay damp and paint and plaster fail.
What is the difference between DPC and DPM?
A DPC is the narrow strip built into the walls just above ground level. A DPM (damp-proof membrane) is the plastic sheet laid under a concrete floor slab. The two should meet so that the floor and the walls are sealed off from ground moisture as one continuous barrier.
How do I know if it is rising damp?
Rising damp shows as a tide mark, blistering paint and white salts low down on the wall, usually on ground-floor walls and worst near the floor. Damp patches higher up, around windows or below a roof or bathroom usually have another cause, such as rain getting in or a leaking pipe.
How do I stop damp on inside walls?
First find the cause: rising damp (no or broken damp-proof course), water coming through the wall from outside, leaking plumbing, or condensation from poor ventilation. Fix the source, let the wall dry, then use a suitable damp-proofing treatment and paint system. Painting over damp alone will not solve it.
Can I fix rising damp myself?
Simple causes often can be fixed yourself - lowering soil or paving that covers the DPC, or cutting back plaster that bridges it. Where the DPC is missing or has failed, a damp-proofing injection treatment is an option; follow the product instructions exactly or use a damp-proofing contractor.
Related guides
Delivery from HPM
Parcels up to 50 kg are delivered by courier anywhere in South Africa, with the rate shown at checkout. Heavy building materials such as cement, bricks, sand, stone and timber are delivered by our own trucks in the Western Cape, and any order can be collected free in Struisbaai.
WhatsApp 076 370 4367 for a quote, call 028 435 6331 or email [email protected].
General guidance only. Products, sites and building rules differ - always follow the product data sheet and your approved plans, and check with your municipality or a registered professional where the work is structural, electrical or needs approval. More short answers: Building Facts & Advice.