Mon-Fri: 7:30am - 5:15pm | Sat: 8:00am - 1:00pm

By HPM Bouhandelaars · Updated · 5 min read · Walls, concrete and paving

In short

  • Work in square metres: wall length x height, minus doors and windows.
  • A single-skin wall of standard bricks uses about 50 bricks per square metre; a double-skin wall about 100.
  • Add extra for cutting, breakage and waste.
  • Mortar and plaster quantities depend on the mix and the thickness - treat any rule of thumb as a starting point.
  • Use the HPM calculator for quick numbers, or send us your plan for a materials list and quote.

Ordering too few bricks stops the job while you wait for a second load; ordering far too many leaves money stacked in the yard. A reasonable estimate takes ten minutes, a tape measure and a calculator. This guide walks through the steps for a wall of standard clay or cement bricks, with a worked example. If you would rather skip the arithmetic, use the building calculators, or send us your plan and we will work out a materials list and quote.

Step 1: measure the wall

Work in square metres. Measure the length and the height of each wall in metres and multiply them. Then subtract the openings: measure each door and window (width x height) and take those areas off. Add the walls together to get the net wall area.

Small openings such as air bricks are not worth subtracting. Gables are triangles: half the width multiplied by the height of the triangle.

Step 2: bricks per square metre

A standard South African brick is 222 mm long, 106 mm wide and 73 mm high. Laid in a single skin (a "half-brick" wall, about 106 mm thick plus plaster) with 10 mm mortar joints, each brick with its share of joint covers 232 x 83 mm of wall face. That works out to about 52 bricks per square metre, which builders round to 50 and then add waste.

  • Single-skin wall: about 50 bricks per square metre.
  • Double-skin wall (a "one-brick" wall, the normal outside wall of a house): about 100 bricks per square metre.

Blocks and non-standard bricks are different. For those, work out the face area of one unit including a 10 mm joint and divide one square metre by it, or ask us for the number per square metre.

Step 3: add waste

Bricks break in transport and are cut at corners, openings and the ends of courses. Builders commonly add 5 to 10 percent to the count. Use the higher figure for small jobs, walls with many openings or corners, and face brick, where chipped bricks cannot be hidden under plaster. With face brick it also matters that the whole order comes from one batch, because colour varies slightly between batches - another reason not to run short.

Step 4: cement and sand for mortar

Mortar quantities depend on the mix, the thickness of the joints and how carefully the bricklayer works, so any figure is approximate. A commonly used rule of thumb for general brickwork mortar is in the region of 3 bags (50 kg) of cement and about 0.6 cubic metres of building sand for every 1,000 standard bricks. Treat that as a starting point for a quote, and follow the mix on the cement bag or on your plans. The cement and mix ratios guide explains which cement and which sand to use.

Step 5: plaster, if the wall will be plastered

Plaster is estimated by area and thickness. Measure the area to be plastered - remember that a wall plastered on both sides has twice the area - and decide on the thickness; 10 to 15 mm is typical on brickwork. A commonly used rule of thumb is roughly 10 bags of cement and 2 cubic metres of plaster sand for 100 square metres of plaster 15 mm thick. Rough or uneven brickwork takes more. Use plaster sand, not building sand, for plaster.

A worked example

An internal single-skin wall, 5 m long and 2.6 m high, with one door opening of 0.9 x 2.1 m, plastered on both sides:

Gross area5 x 2.6 = 13.0 m²
Less the door0.9 x 2.1 = 1.9 m², leaving 11.1 m²
Bricks11.1 x 52 = about 580
Plus 10% wasteabout 640 bricks
Mortar (rule of thumb)640 / 1,000 x 3 bags = about 2 bags of cement, and about 0.4 m³ of building sand
Plaster area11.1 x 2 sides = 22.2 m²
Plaster at 15 mm (rule of thumb)22.2 / 100 x 10 bags = about 2.2, so 3 bags of cement, and about 0.5 m³ of plaster sand

Round up to whole bags and to the quantities sand is sold in. On a small job the rounding matters more than the arithmetic: nobody delivers 0.2 of a bag.

What estimates usually leave out

  • Foundations. The concrete footing under the wall is a separate calculation (length x width x depth in cubic metres) and, for anything structural, an engineer's or the plan's specification.
  • Damp-proof course. DPC runs the full length of every wall, plus laps. See damp-proofing basics.
  • Lintels. Every opening in a load-bearing wall needs a lintel to carry the brickwork above it. The size and the bearing on each side are shown on your plans.
  • Brick reinforcement and wall ties where the plans call for them.
  • Sills, air bricks, door and window frames that are built in as the wall goes up.
  • Water and tools: a mixing surface or mixer, wheelbarrow, trowels, a builders line, levels and a bolster for cutting.

Boundary walls, retaining walls and anything load-bearing must be built to approved plans; the wall thickness, piers, foundations and reinforcement are not something to estimate from a general guide. Most municipalities require approved plans for boundary walls above a set height, so check before you order.

Bricks, blocks, cement and sand are heavy materials. HPM delivers them with its own trucks in the Western Cape (minimum 4 000 kg or R 10 000 per truck delivery outside Struisbaai), or you can collect in Struisbaai. Send your measurements or plan by WhatsApp to 076 370 4367 and we will quote for the materials and delivery together.

What you need

These links open the matching products in the HPM online store, with live prices (incl. VAT) and stock.

Questions and answers

How do I work out how many bricks or how much cement I need?

As a rough guide, a standard brick wall uses about 50 bricks per square metre for a single skin and about 100 for a double skin, plus extra for waste and breakage. Mortar and plaster quantities depend on the mix and thickness. Send us your plans or measurements and we can help you work out a materials list and quote.

How many bricks are in a square metre?

With standard bricks (222 x 106 x 73 mm) and 10 mm mortar joints, a single-skin wall takes about 52 bricks per square metre, usually rounded to 50 before waste is added. A double-skin wall takes twice as many.

How much extra should I order for waste?

Builders commonly add 5 to 10 percent to the brick count for cutting and breakage - more for walls with many corners, openings or cut courses. It is cheaper than a second delivery for a few hundred bricks.

Do I need a lintel above windows and doors?

Yes - every opening in a load-bearing wall needs a lintel (precast concrete or steel) to carry the brickwork above it. The lintel size and the bearing on each side depend on the opening width and the load, as shown on your plans.

Can HPM deliver bricks and cement outside the Western Cape?

No. Bricks, blocks and cement are heavy materials and travel on HPM's own trucks, which deliver in the Western Cape only. Tools, fixings and other parcels up to 50 kg go by courier anywhere in South Africa.

Delivery from HPM

Parcels up to 50 kg are delivered by courier anywhere in South Africa, with the rate shown at checkout. Heavy building materials such as cement, bricks, sand, stone and timber are delivered by our own trucks in the Western Cape, and any order can be collected free in Struisbaai.

WhatsApp 076 370 4367 for a quote, call 028 435 6331 or email [email protected].

General guidance only. Products, sites and building rules differ - always follow the product data sheet and your approved plans, and check with your municipality or a registered professional where the work is structural, electrical or needs approval. More short answers: Building Facts & Advice.